Our open source Flight control, provide technical support, you can search on internet if need more information and adjustment.
Important statement: Our F3 adopts original STM32F303CCT6 chipset, not STM32F303CBT6 which adopted by some other merchant. The storage of original STM32F303CCT6 chipset is 256K, but the storage of STM32F303CBT6 chipset is only 128K.Currently,the latest F3 firmware is near 120K,use STM32F303CBT6 chipset will cause fail update firmware or fail to run latest firmware if keep updating firmware. Hobbyist, resellers and distributors, please sharp your eyes. Below are the compare photo of original STM32F303CCT6 and STM32F303CBT6.
*Size: 36x36mm, mounting hole 30.5mm.
*Weight: 5g.
*processor: stm32f3 CPU.
*Large volume storage (standard and luxury)
*MPU6050 accelerometer and gyroscope.
*MS5611 barometer(luxury)
*HMC5883 compass(luxury)
* MicroUSB plug
*4 4pin jst-sh plug(I2C,SWD,2xuart)
*2X 8pin jst-sh plug(PPM,PWM, serial incept,GPIO,ADC,3V,5V,GND)
*8x 3pin though-holes for pin headers for ESC/Servo connections
•2x 4pin though-holes for pin headers for 2x serial ports
Wiring: 2*8P JST-SH Turn the DuPont first line
2*4P JST-SH Turn the DuPont first line
Our shop can provide related technical support.
Our NAZE32 F3 serial Flight control all are official standard hardware, produce according to official original version. Reliable and stable.
The SPRacing F3 Flight Controller was designed to give awesome flight performance based on tried and tested sensors whilst also providing unparalleled and I/O capabilities in a small and extremely lightweight form-factor using a next-generation CPU.The SPRacingF3 gives you all the features you need for the heart of your aircraft, whether you're into FPV racing, acrobatic flying or aerial photography it's perfect.
I/O uses all the features all the time; e.g. Connect your OSD SmartPort SBus GPS LED Strip Battery Monitoring Sonar 8 motors - all at the same time!
On-board high-capacity black box flight log recorder - optimize your tuning and see the results of your setup with out guesswork (Acro and Deluxe).
Next-generation STM32 F3 processor with hardware floating point unit for efficient flight calculations and faster ARM-Cortex M4 core.
Stackable design - perfect for integrating with OSDs and power distribution boards.
16 PWM I/O lines for ESCs, Servos and legacy receivers. 8 available on standard pin headers. 8 via side mounted connectors.
Full support for Mult, OneShot ESCs for easy PID tuning and a sharper response.
Supports SBus, SumH, SumD, Spektrum1024/2048, XBus, PPM, PWM receivers. No external inverters required (built-in).
Dedicated output for programmable LEDs - great for orientation, racing and night flying.
Dedicated I2C port for connection of OLED display without needing flight battery.
Battery monitoring ports for voltage and current.
Sonar support for precision low-altitude hold.
Buzzer port for audible warnings and notifications.
Developer friendly debugging port (SWD) and boot mode selection, unbrickable bootloader.
Symmetrical design for a super tidy wiring.
Wire up using pin headers, JST-SH sockets or solder pads. Use either right-angled or straight pin-headers
Barometer mounted on the bottom of the board for easy wind isolation.
Loop times up to ~2x as fast as previous-generation STM32F1 based boards.
can be configured to suit your needs using a cross-platform GUI (Windows/OSX/Linux).
Supports a variety of aircraft, tricopters, quadcopters, hexacopters, octocopters, planes and more.
Available in Acro and Deluxe versions.
The SPRacingF3 runs the open-source Cleanflight flight control (FC) software which has an ever-growing community of friendly developers and users. Being open-source means that you too can contribute to the system.
Cleanflight comes with a detailed manual that is reviewed and maintained by the Cleanflight developers and community. No more out-of-date wiki pages and second-hand information.
See http://cleanflight.com for links to the manual. PDF copies can be downloaded from the github releases pages. Ensure you reference the manual that is appropriate to your firmware version.