Sale! DALRC Mini QOSD for QAV250 ZMR250 280 FPV Racing

DALRC Mini QOSD for QAV250 ZMR250 280 FPV Racing


US$ 49.99




1:Battery voltage display (single voltage 3.6V by flashing a warning, 2-6S automatic recognition)
2:Attitude angle display (P: pitch angle R: Roll angle)
4:Number of GPS satellites (6 stars over automatically record at home, short press the button to manually record home)
5:Home direction indicator (square in the middle, the front of the screen that is the direction of home)
6:The total voyage
7:Distance from home
9:Azimuth (home and aircraft line and just north of where the angle, measured clockwise)
10:Head toward (just north of 0 °, calculated clockwise)
11:Remote RSSI signal strength (RSSI output requires Receiver support, not displayed by default)
12:Horizon (coincidence horizon, to facilitate the observation flight attitude)
13:Center of the screen icon (supports three kinds of icons, or off))
14:vertical speed
15:Latitude and longitude (LON: longitude LAT: latitude E:East W:West S:South N:North)
16:Flight time (can be cleared by the key or remote control)
17:Maximum flight speed (default is not shown)
18:Maximum line distance (default is not shown)

QOSD data can be customized switch, the user can be displayed or close any one content, QOSD interface can not change the display position, CUSTOM custom interface can change the display position

Programmable: YES

Setup :

1: First page setup menu
2:GPS baud rate settings: Optional GPS to 38400 baud, no need to set, if you do not take GPS, GPS baud rate is set to turn off the OSD OFF closed NO GPS Home Tips
3:Voltage calibration: use the meter to measure the battery voltage, and then set to the same voltage
4:Remote RSSI signal calibration: Turn on the transmitter and receiver, the remote control close to the receiver, RSSI line access, click recalibration
5:Video format settings: PAL and NTSC, such as the discovery of the insertion of the camera without an image or without OSD overlay, pull out the camera to change the system can be (the display should be PAL or NTSC standard)
6:OSD display type: QOSD for the default interface, such as QOSD interface data display is not complete, switch to QOSD1. CUSTOM for the custom interface, each content can change the location (can be changed in 10 MENU CUSTOM)
7:Height Gets equipment: BARO is barometer. You can also use the GPS, is recommended barometer
8:Auto setting home: ON OFF
9:Horizon Display:ON OFF
10:Custom Menu
11: second page setup menu
12:Directions acquisition device (AUTO, COMPASS, GPS, recommend the use of compass)
13:Mounting direction (FRONT BACK LEFT RIGHT, direction arrows GOSD ago)
14:The rolling sense (the horizon does not coincide or the reverse is set, generally without setting).
15:Pitch sense (the horizon does not coincide or reverse when set, generally without setting)
16:Boot sereen:ON OFF
17:Compass Calibration: horizontal rotating clockwise circle, then clockwise rotation of the front down, the calibration was successful
18:Horizontal calibration: the level of the aircraft, after entering the automatic calibration, automatic exit the calibration, the installation is recommended to do a horizontal calibration
19:Reset: Restores all settings GOSD
20:Exit menu
21: third page setup menu (MENU CUSTOM)
22:Voltage display (switch position adjustment)
23:Time display (switch position adjustment)
24:Speed display (switch position adjustment)
25:Height of the display (switch position adjustment)
26:Direction of home display (switch position adjustment)
27:From the home display (switch position adjustment)
28:Total flight display (switch position adjustment)
29:Remote RSSI signal strength display (switch position adjustment)
30:Vertical speeddisplay(switch position adjustment)
31: fourth page setup menu (MENU CUSTOM)
32:Latitude and longitude display (switch position adjustment)
33:The number of satellites display (switch position adjustment)
34:Azimuth display (switch position adjustment)
35:Head direction display (switch position adjustment)
36:Attitude angle display (switch position adjustment)
37:The maximum distance display (switch position adjustment)
38:Maximum speed is displayed (switch position adjustment)
39:Center of the screen display (switch position adjustment)
40:Previous Menu
41:Exit menu
42:fifth page of the setup menu (CUSTOM MENU submenu)
43:Display (ON OFF)
44:Row (from the left count)
45:Column (start counting from the top)

Package Include:

1 x QOSD
1 x GPS